Balance Bike & Scooter Holder for UPPAbaby Ridge

They ride the whole way to the trail. They do not ride the whole way back.

That is exactly what this holder is designed to fix.

Our Balance Bike & Scooter Holder clips onto the side frame tube of your UPPAbaby Ridge and gives the bike its own place to ride. Two cradles sit along the tube with their openings facing up, so the bike drops straight in and lifts straight out — no straps to thread, no bungee to fight, no bike over your shoulder for the last mile.

It rides low and outboard of the frame, well inside the footprint of the stroller, because hanging weight high on a stroller is the main way one tips. That is also why it does not go anywhere near the handlebar.

Every order is a matched pair of holders, printed in black.

The stroller, bike and scooter are not included.

Why parents love it

• The bike comes home on the stroller instead of under your arm

• Drops in and lifts out in one motion — nothing to unclip or unthread

• Goes on the left or the right frame tube — one part, your choice of side

• Mounts low and inside the wheelbase, where weight belongs on a stroller

• Takes a balance bike or a kick scooter

• Rated to carry 50 lb — many times what any balance bike weighs

• Leaves the storage basket free for everything else

• A rubber grip strip in each clip holds the pair in place along the tube

• Installs and removes without permanently modifying your stroller

• Made to order and test-fitted on the actual stroller before it ships

Compatibility

UPPAbaby Ridge V1 — the original Ridge, launched in 2021. That is the frame this was designed on and test-fitted to. You can check yours in a few seconds: the model number is printed on the left side of the frame above the rear wheel, and the V1 reads 1401-RDG-US.

Ridge V2 (2026) has not been checked yet. The V2 is not a full redesign, but its fold mechanism changed, and this holder sits on the part of the frame nearest that hardware — so we are not going to claim it until we have had one on the bench. If you have a V2 and you want this, message us. We would rather tell you honestly than sell you a part that does not seat.

Either side. The Ridge's left and right frame tubes are the same section, so the same pair fits whichever side suits how you walk. Both holders go on that one tube.

Where it goes on the tube. On the straight run of the side frame tube, clear of the leg bracket and of the notched section further along. There is room to space the pair to suit your bike.

What fits in the cradle. The cradle is 46 mm (1.8 in) across on the inside and about 55 mm (2.2 in) deep. Measure whatever will rest in it — the top tube of a balance bike, or the steering column of a kick scooter — at its widest point. Anything up to 46 mm drops straight in. That is the number to check, not the brand on the bike.

Please verify your stroller model before ordering.

Stroller, bike and scooter are sold separately and are not included with this product.

How it works

Tilt the cradle up slightly, hook the top arm over the frame tube, then push the bottom in and up until it clicks. No tools, nothing to tighten, nothing to over-tighten.

The hook is deliberately deep — about 12 mm of bearing down the inboard face — and it sits where the load pushes, so the weight of the bike closes the clip rather than prying it open. A push-on clamp does the opposite: the bike's leverage walks it off the corner. We know, because that is what an earlier design did on the bench, and it is the reason this one is shaped the way it is.

A rubber grip strip sits in a pocket on the outboard face of each clip, so the pair does not creep along the tube.

The bike rests in the cradles with its own weight holding it down. Lift it out the same way it went in.

Remove it before you fold the stroller

The holders must come off before the stroller is folded. Folding with them installed can damage the holders, the bike, or the frame itself. Take the bike out first, then the holders, then fold.

With the pair fitted and the bike loaded, the bike sits clear of the stroller's wheels.

What it's rated for

Rated to carry 50 lb. That is many times what a balance bike or a kick scooter weighs, which is the point — the rating is not the thing you should have to think about on a walk to the trail. The figure we publish is never more than half of what the part was tested to carry.

It is not a child restraint and is not certified to any child restraint standard. It must never be used to support, restrain or carry a child. It carries the bike or scooter only when no one is on it — never put a child on a bike or scooter while it is in the holder, and never let a child sit, stand, lean or climb on the holder or on what it is carrying. It is not a seat, a step or a perch.

More from Stroller House

• Everything we make for UPPAbaby — the Vista parts live here too.

• Stroller adapter fit guide — what fits what, across brands, in one place.

Frequently asked questions

How much weight will it hold?

The pair is rated to carry 50 lb, which is many times what a balance bike or kick scooter weighs. What it is not built for is a person's weight: no child may sit, stand, lean or climb on the holders or on a mounted bike, and no one may ride a bike or scooter while it is in them.

Will it fit a Ridge V2?

We do not know yet, so we are not claiming it. The V2 arrived in 2026 with a different fold mechanism, and this holder mounts near that hardware. We will test one and update this listing. Message us if you have a V2 — knowing people want it is what moves it up the queue.

Left side or right side?

Either. The Ridge's two frame tubes have the same section, so the same pair fits both. Put them where you want them.

Does the bike need to be strapped in?

No. It sits in the cradles under its own weight. That is the point — one motion in, one motion out, while you are holding everything else.

How far apart do the two holders sit?

That is yours to set. Space them so your bike hangs level, then leave them there — the grip strip keeps them put.

Will they slide down the frame tube?

No. A rubber grip strip sits in a pocket on the outboard face of each clip, and the clip is shaped so the bike's weight tightens it rather than loosening it.

How many pieces come in the box?

Two. The holder ships as a matched pair, printed in black — the only color we print. Both pieces go on the same frame tube.

Does the bike come with the holder?

No. This listing is for the pair of holders only. The stroller, bike and scooter must be purchased separately.

Has this been tested?

Yes — the actual printed part, loaded on the bench, before it was ever listed. Nothing goes on sale here until it has been tested rather than modeled, and every part is test-fitted on the real stroller before it ships. Where we publish a weight figure, that figure is never more than half of what the part was tested to carry — a safety factor of at least two. We don't publish the bigger number, because margin you advertise is margin people spend.

What is it made from?

PETG — tougher and far more heat-tolerant than the PLA most printed parts use. Each holder is printed with six solid wall loops, because on a part shaped like this the strength lives in the skin rather than the infill. Black is the only color we print.

Do I have to modify my stroller?

No. The holders clip onto the existing frame tube and do not require permanent modification of the stroller or the bike.

Is this made by UPPAbaby?

No. This is an independently designed aftermarket accessory made by Stroller House. We are not affiliated with, sponsored by, authorized by, or endorsed by UPPAbaby.

Made to order, and fitted before it ships

Each pair is printed after you order it, then test-fitted on the actual stroller — we own the Ridge these were designed on, and the photos on this listing are that stroller — and inspected before it goes in the box. You'll get tracking as soon as it ships.

If something is wrong

If a holder arrives damaged, doesn't seat on your frame, or isn't what you ordered, send a photo within 30 days and we'll replace it at our cost — you won't need to ship the original back. Full details in returns.

Before you use it

This is an aftermarket accessory made by Stroller House, not an UPPAbaby part, and fitting it may affect your stroller's warranty. It is not a child restraint and is not certified to any child restraint standard. It must never be used to support, restrain or carry a child. It carries the bike or scooter only when no one is on it — never put a child on a bike or scooter while it is in the holder, and never let a child sit, stand, lean or climb on the holder or on what it is carrying. It is not a seat, a step or a perch. Remove the holders before you fold the stroller. Check that both are seated and the bike is settled in the cradles before each use, and stop using them at the first sign of cracking, whitening, deformation or movement. Keep printed parts out of hot parked cars. Always follow the stroller manufacturer's instructions and weight limits. See installation and safety.

UPPAbaby® and Ridge® are trademarks of UPPAbaby. Stroller House is not affiliated with, endorsed by, sponsored by, or connected to UPPAbaby or its parent companies. Brand and model names appear here only to identify the products this accessory is designed to fit.